Dynamic Santiago Elite 2-person Ultra Low EMF FAR Infrared Sauna

A compact, luxury two-seater built for daily wellness at home. Santiago Elite uses PureTech™ ultra-low EMF carbon panels (3–5 mG measured 2–3" from the panel) arranged around the cabin for fast, even heat. Canadian hemlock, a tempered-glass door with side window, and interior LED controls make it a beautiful, plug-and-play upgrade for any indoor space.

Highlights

• Ultra-low EMF PureTech™ heating: 7 FAR infrared carbon panels (2 rear, 2 side + 2 side, 1 under bench) for surround heat.

 

• True 2-person capacity with full-height glass door and hemlock construction.

 

• Plug & play: 120V / 15A (non-GFCI), standard household outlet; dedicated circuit recommended.

 

• Therapeutic range: Ideal 118–132°F; can reach up to 140°F.

 

• Indoor-only design with quick, tool-light assembly.

Specifications

• Model: Dynamic Santiago Elite – 2-Person FAR Infrared Sauna

 

• Capacity: 2 adults

 

• Heating Elements: 7 PureTech™ ultra-low EMF carbon panels (3–5 mG @ 2–3")

 

• Wood: Natural reforested Canadian hemlock

 

• Glass: Clear tempered glass door with side window

 

• Temperature: 118–132°F ideal; up to 140°F

 

• Electrical: 120V / 15A, non-GFCI plug-and-play (dedicated outlet recommended)

 

• Use: Indoor only

 

• Exterior Dimensions: 40" L x 46" W x 75" H

 

• Product Weight: ~300 lb

 

• Shipping (LTL): 2 cartons (A ~258 lb, B ~64 lb); Pallet approx. 20" L x 78" W x 53" H, pallet wt. ~370 lb

Controls, Lighting & Audio

• Controls: Interior LED control panel for time & temperature.

 

• Lighting: Interior chromotherapy color system + Red-Light feature.

 

• Audio: Bluetooth + 3.5mm MP3 aux with built-in speakers.

In the Crate (What’s Included)

• Pre-assembled wall panels, base/floor, roof panel, tempered-glass door assembly

 

• Bench & heater panel set (factory-installed)

 

• Interior LED control panel & chromotherapy/Red-Light fixture (factory-wired)

 

• Hardware & fasteners, power cord

 

• Owner’s manual & assembly guide

Installation

1. Location: Dry, level indoor surface with standard ceiling height.

2. Power: One dedicated 120V / 15A non-GFCI receptacle within reach of the cord.

3. Clearance: Leave a few inches around the unit for ventilation and assembly.

4. Assembly: Typically 45–90 minutes with two adults. Panels align and latch together; minimal tools (Phillips screwdriver/step stool) needed.

5. Break-in: After assembly, run the sauna on high for 30–45 minutes with door slightly open to air out.

FAQs

Does this require a special outlet?

It runs on 120V / 15A (standard US household). Use a non-GFCI receptacle; a dedicated circuit is strongly recommended.

 

Is it safe in apartments or upstairs?

Yes—no plumbing, no venting. Ensure the floor is level and can support ~300 lb plus occupants.

 

How hot does it get?

Ideal therapy range is 118–132°F; unit can reach up to 140°F depending on room temp and setup.

 

What EMF level should I expect?

Panels are rated ultra-low EMF (3–5 mG) measured 2–3 inches from the panel.

 

Can I put it outside or in a garage?

No. This model is indoor-only. Keep away from damp areas or extreme temps.

 

How many people are needed for assembly?

Two adults. Typical assembly time is under 90 minutes.

 

What maintenance is required?

Wipe interior surfaces with a soft, dry cloth after use and keep the door glass clean. (Avoid harsh chemicals.)