Dynamic Versailles Elite 2-person Ultra Low EMF FAR Infrared Sauna

The Dynamic Versailles Elite fits two comfortably in a compact footprint, pairing 6 ultra-low EMF FAR-infrared carbon heaters with Canadian hemlock, a tempered-glass door with side window, chromotherapy + red-light, and Bluetooth audio. It runs on a standard 120V/15A (non-GFCI) dedicated outlet for true plug-and-play installation.

Highlights

• 6 Ultra-Low EMF carbon heaters (≈3–5 mG measured 2–3" from panels)
  Layout: 2 rear • 1 left • 1 right • 1 under bench • 1 floor board

 

• Full 2-person bench; compact footprint

 

• Natural Reforested Canadian Hemlock interior/exterior

 

• Clear tempered-glass door + side window

 

• Chromotherapy color lighting + dedicated Red-Light feature

 

• Bluetooth + MP3 aux with built-in speakers

 

• Interior/Exterior LED control panels

 

• Temp range: 118–132°F (heats up to ~140°F)

 

• Electrical: 120V / 15A, non-GFCI dedicated outlet recommended

 

• Indoor use only; curbside LTL delivery on pallet

Specifications

• Model: Dynamic Versailles Elite (2-Person)

 

• Capacity: 2

 

• Exterior dimensions: 42" L × 47" W × 75" H
  (Roof overhang adds ~2" to length; total ≈ 44" L)

 

• Product weight: 335 lb

 

• Wood: Natural Reforested Canadian Hemlock

 

• Glass: Clear tempered door with side window

 

• Heating system: 6 Ultra Low EMF FAR-infrared carbon panels (layout above)

 

• Temperature: 118–132°F typical (max ~140°F)

 

• Electrical service: 120V / 15A, non-GFCI plug-and-play (dedicated circuit recommended)

 

• Location: Indoor use only

 

• Delivery: Curbside, palletized LTL freight

 

 

Shipping (cartons & pallet)

• Carton A: 10" L × 48" W × 73" H • 250 lb

 

• Carton B: 8" L × 42" W × 47" H • 88 lb

 

• LTL pallet dims: 20" L × 74" W × 54" H • Pallet weight: 365 lb

Controls, Lighting & Audio

• Dual LED control panels (interior & exterior)

 

• Chromotherapy color lighting system + Red-Light feature

 

• Bluetooth & MP3 auxiliary audio with built-in speakers

Everything Included

• Pre-wired wall/roof/floor panel set with integrated heaters

 

• Tempered-glass door assembly & side window panel

 

• Bench & floor sections

 

• Hardware & fasteners; interlock wiring harnesses

 

• Power cord (120V) & quick-start assembly manual

 

• Ships in 2 cartons on one pallet (see shipping section)

Installation

1. Power: 120V / 15A non-GFCI dedicated outlet within reach of the cord.

2. Space: Minimum ceiling height 84"+ recommended; leave ~2–3" clearance at sides/rear for airflow and assembly.

3. Surface: Flat, dry, level indoor floor (tile, wood, vinyl, low-pile carpet OK). Avoid wet areas & radiant-heated floors.

4. Assembly: 2 adults; panels latch together—typical build time 45–75 minutes.

5. First use: Wipe interior dust, then run a burn-in cycle (30–45 min at ~130°F) with door slightly ajar.

6. Operation: Preheat 20–30 min to 120–130°F before sessions.

FAQs

What makes it “ultra-low EMF”?

Carbon panels and shielding keep readings around 3–5 mG measured 2–3 inches from the panel surface.

 

Can I plug it into any household outlet?

Yes—120V/15A. Use a dedicated, non-GFCI circuit. Avoid extension cords.

 

Is ventilation required?

Normal room ventilation is fine. Keep a few inches of clearance around exterior panels and don’t block floor/roof vents.

 

How hot will it get?

Typical sessions run 118–132°F. The cabin can reach ~140°F depending on ambient conditions.

 

Can it go in a garage or on carpet?

Indoors only, protected from moisture. Low-pile carpet is fine if the surface is level and dry.

 

Can I move it later?

Yes. It disassembles back into panel sections; save the hardware and manual.